DIN 976-1 dimensions — Stud Bolt / Threaded Rod
2016-09 edition, current · 27 sizes, M2 – M64 see the cross-reference →
✓We supply to DIN 976-1. Name it on your order.
DIN 976-1 dimensions
| Thread size | PThread Pitch (mm) | Clearance holefine / medium / coarse (mm) | Tap drillcoarse pitch (mm) |
|---|---|---|---|
| M2 | 0.4 | 2.2 / 2.4 / 2.6 | 1.6 |
| M2.5 | 0.45 | 2.7 / 2.9 / 3.1 | 2.05 |
| M3 | 0.5 | 3.2 / 3.4 / 3.6 | 2.5 |
| M4 | 0.7 | 4.3 / 4.5 / 4.8 | 3.3 |
| M5 | 0.8 | 5.3 / 5.5 / 5.8 | 4.2 |
| M6 | 1 | 6.4 / 6.6 / 7 | 5 |
| M8 | 1.25 | 8.4 / 9 / 10 | 6.8 |
| M10 | 1.5 | 10.5 / 11 / 12 | 8.5 |
| M12 | 1.75 | 13 / 13.5 / 14.5 | 10.2 |
| M14 | 2 | 15 / 15.5 / 16.5 | 12 |
| M16 | 2 | 17 / 17.5 / 18.5 | 14 |
| M18 | 2.5 | 19 / 20 / 21 | 15.5 |
| M20 | 2.5 | 21 / 22 / 24 | 17.5 |
| M22 | 2.5 | 23 / 24 / 26 | 19.5 |
| M24 | 3 | 25 / 26 / 28 | 21 |
| M27 | 3 | 28 / 30 / 32 | 24 |
| M30 | 3.5 | 31 / 33 / 35 | 26.5 |
| M33 | 3.5 | 34 / 36 / 38 | 29.5 |
| M36 | 4 | 37 / 39 / 42 | 32 |
| M39 | 4 | 40 / 42 / 45 | 35 |
| M42 | 4.5 | 43 / 45 / 48 | 37.5 |
| M45 | 4.5 | 46 / 48 / 52 | 40.5 |
| M48 | 5 | 50 / 52 / 56 | 43 |
| M52 | 5 | 54 / 56 / 62 | 47 |
| M56 | 5.5 | 58 / 62 / 66 | 50.5 |
| M60 | 5.5 | 62 / 66 / 70 | - |
| M64 | 6 | 66 / 70 / 74 | - |
27 of 27 sizes shown. Clearance holes are fine / medium / coarse to ISO 273; tap drill is for the coarse pitch.
What we supply to DIN 976-1
2 materials| Material | Property class | Finish |
|---|---|---|
| Carbon Steel | 4.8 · 8.8 | Zinc Plated · Dacromet · Blackened · Phosphate · Plain · Hot Dip Galvanized |
| Stainless Steel | A2-70 · A4-80 | Plain · Passivated |
Property classes
ISO 898-1 · ISO 3506-1| Class | Rm min. | Yield requirement | Elongation requirement | Hardness | Typical use |
|---|---|---|---|---|---|
| 4.8 | 420 MPa | Rpf min. 340 MPa (not a test value) | Af min. 0.24 | 130 - 220 HV | Light-duty non-structural work; the low-cost class for large sizes carrying little load. |
| 8.8 (d <= M16) | 800 MPa | Rp0.2 min. 640 MPa | A min. 12 % | 250 - 320 HV | The general-purpose structural class — steel-to-steel joints, machinery, vehicle assembly. Assume this if no class is stated. |
| 8.8 (d > M16) | 830 MPa | Rp0.2 min. 660 MPa | A min. 12 % | 255 - 335 HV | |
| A2-70 | 700 MPa | Rp0.2 min. 450 MPa | 0,4d mm | - | Cold-worked austenitic stainless, typically 304 — outdoor, wet and food service away from chlorides. |
| A4-80 | 800 MPa | Rp0.2 min. 600 MPa | 0,3d mm | - | The strongest 316-type class; marine and chemical service where 70 does not carry the load. |
These values meet the requirements of ISO 898-1 / ISO 3506-1. We supply to these classes and issue the matching mill certificate and third-party test report with your order.
